Do fire protection installers need SWMS?

Yes. Fire protection work typically involves working at heights (installing sprinklers and detectors at ceiling level), working in confined spaces (risers, ceiling cavities), and electrical work — all high-risk activities under WHS Regulations s.291.

What fire protection systems are covered?

Our pack covers fire sprinkler systems (AS 2118), fire detection and alarms (AS 1670), fire doors (AS 1905), hydrants and hose reels (AS 2419), fire dampers, and passive fire protection — each with system-specific hazard controls.

Is electrical work for fire systems included?

Yes. Our detection and alarm SWMS covers low-voltage wiring, cable installation in ceiling spaces, electrical isolation procedures, and commissioning — addressing both electrical and working-at-height hazards.

Fire Protection JSA

Fire services, sprinkler systems, fire door installation, and detection

Fire Protection Complete Pack

8 documents — everything you need for fire protection compliance.

$120 $102 Save $18 — 15% off ends 30 June 2026 Buy Complete Pack See a sample first →

Not the right fit? Refund available if documents don't match your trade.

Also available for Fire Protection: SWMS — from $67.96 Toolbox Talk — from $21.21 Risk Assessment — from $33.96 Induction — from $21.21 SOP — from $33.96 Emergency — from $42.46

Fire protection installation involves working at heights to install sprinkler systems and detection equipment, working in confined ceiling spaces, and handling pressurised piping systems — all requiring documented SWMS under WHS Regulations.

Our fire protection SWMS pack covers 8 activities including fire sprinkler installation, fire door fitting, smoke detection and alarm systems, fire hydrant and hose reel installation, fire damper installation, and passive fire protection (fire stopping). Documents address hazards such as falls from height, working in confined ceiling spaces, pressurised pipe testing, electrical work for detection systems, and hot work for pipe joining.

Key Hazards Covered

Falls from height during sprinkler installation
Working in confined ceiling and riser spaces
Pressurised pipe testing and burst risk
Electrical hazards during detection system wiring
Hot work for copper and steel pipe joining
Manual handling of heavy pipe and fittings

Relevant Australian Standards

AS 2118 Automatic fire sprinkler systems
AS 1905 Fire-resistant doorsets
AS 1670 Fire detection and alarm systems
AS 2419 Fire hydrant installations

Individual Documents — $16.96 each

	Document	Price
	Fire Sprinkler System Installation — Safe Work Method Statement Safe work procedures for installation of fire sprinkler systems including pipe fitting, sprinkler head installation, valve assemblies, and hydrostatic pressure testing in accordance with AS 2118. What's inside this document 5 work steps 8 hazards identified 8 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.79 (falls — minimising risk) WHS Reg 2011 r.214 (management of risks to health and safety) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Fire Door and Frame Installation — Safe Work Method Statement Safe work procedures for installation of fire-resistant doorsets including fire-rated frames, door leaves, intumescent seals, self-closers, and associated hardware in compliance with AS 1905.1. What's inside this document 4 work steps 5 hazards identified 5 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.214 (management of risks to health and safety) WHS Reg 2011 r.213 (duty to identify hazards) WHS Reg 2011 r.39 (provision and use of plant) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Smoke and Heat Detection System Installation — Safe Work Method Statement Safe work procedures for installation of fire detection and alarm systems including smoke detectors, heat detectors, manual call points, alarm panels, and associated cabling in accordance with AS 1670.1. What's inside this document 4 work steps 5 hazards identified 5 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.147 (electrical work — general) WHS Reg 2011 r.214 (management of risks to health and safety) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Fire Hydrant and Hose Reel Installation — Safe Work Method Statement Safe work procedures for installation of fire hydrant systems and hose reels including large-bore pipework, hydrant valve assemblies, booster connections, and hydrostatic testing to AS 2419.1. What's inside this document 5 work steps 7 hazards identified 7 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.214 (management of risks to health and safety) WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.39 (provision and use of plant) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Passive Fire Protection (Fire Stopping, Intumescent Coatings) — Safe Work Method Statement Safe work procedures for installation of passive fire protection systems including fire stopping of penetrations, intumescent coating of structural steel, fire collars, and fire-rated ductwork wrapping. What's inside this document 4 work steps 6 hazards identified 6 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.214 (management of risks to health and safety) WHS Reg 2011 r.351 (hazardous chemicals — duties of PCBU) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Fire Extinguisher Installation and Servicing — Safe Work Method Statement Safe work procedures for installation, inspection, and servicing of portable and wheeled fire extinguishers including wall mounting, signage placement, pressure testing, and agent refilling. What's inside this document 4 work steps 5 hazards identified 5 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.214 (management of risks to health and safety) WHS Reg 2011 r.213 (duty to identify hazards) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Emergency and Exit Lighting Installation — Safe Work Method Statement Safe work procedures for installation, wiring, and testing of emergency lighting and illuminated exit signs in compliance with AS 2293.1 and AS/NZS 3000. What's inside this document 4 work steps 5 hazards identified 5 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.147 (electrical work — general) WHS Reg 2011 r.148 (persons carrying out electrical work) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96
	Fire-Rated Penetration Sealing — Safe Work Method Statement Safe work procedures for sealing fire-rated penetrations in walls, floors, and ceilings using tested and approved fire stopping systems including sealants, mortars, wraps, pillows, and collars. What's inside this document 4 work steps 5 hazards identified 5 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011 r.78 (falls — general duty) WHS Reg 2011 r.351 (hazardous chemicals — duties of PCBU) WHS Reg 2011 r.214 (management of risks to health and safety) PPE Requirements (with AS/NZS standards) Hard hat (Type 1) (AS/NZS 1801) Safety footwear (steel cap) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Hi-visibility vest (Class D/N) (AS/NZS 4602.1) Gloves (task-appropriate) (AS/NZS 2161.1) Australian Standards Referenced AS/NZS 1801 — Occupational protective headwear AS/NZS 2210.3 — Occupational protective footwear	$16.96

Fire Protection JSA — Common Questions

What is the difference between a JSA and a SWMS?

A SWMS is a legal requirement for high-risk construction work and must include detailed control measures and worker sign-off. A JSA is a simplified hazard analysis used for daily planning, toolbox meetings, and non-HRCW tasks. Many businesses use both.

When should I use a JSA?

Use a JSA for daily pre-start meetings, when introducing new workers to a task, for non-high-risk activities, or as a quick reference during toolbox talks.

Can a JSA replace a SWMS?

No. If the work is classified as high-risk construction work under WHS Regulations, a SWMS is legally required. A JSA complements a SWMS but cannot replace it for HRCW.

Are your JSA documents editable?

Yes. All JSA documents are delivered in editable Word (.docx) format with your business details pre-filled.

Last updated: March 2026

Fire Protection JSA

Fire Protection Complete Pack

Individual Documents — $16.96 each

Fire Protection JSA — Common Questions

Other Trades You Might Need