Do I need a SWMS for roofing work?

Yes. Roofing work involves working at heights of 2 metres or more, which is specifically classified as high-risk construction work under WHS Regulations s.291(1)(a). A SWMS must be prepared before any roofing work commences.

What fall protection is required for roofing?

Our roofing SWMS documents specify a hierarchy of fall protection controls: edge protection systems (AS/NZS 4994.1), safety mesh, full body harnesses with lanyards (AS/NZS 1891.1), and administrative controls including exclusion zones below.

Are roof restoration and re-roofing covered?

Yes. Our pack includes dedicated SWMS for roof restoration covering asbestos identification (pre-1990 roofs), old material removal, surface preparation, coating application, and working on fragile deteriorated surfaces.

Roofing Toolbox Talk

Roof tiling, sheeting, restoration, gutters, and height safety

Roofing Complete Pack

8 documents — everything you need for roofing compliance.

$150 $127 Save $22 — 15% off ends 30 June 2026 Buy Complete Pack See a sample first →

Not the right fit? Refund available if documents don't match your trade.

Also available for Roofing: SWMS — from $67.96 JSA — from $16.96 Risk Assessment — from $33.96 Induction — from $21.21 SOP — from $33.96 Emergency — from $42.46

Roofing work is classified as high-risk construction work under WHS Regulations s.291(1)(a) due to the inherent risk of falls from 2 metres or more. A SWMS is mandatory for all roofing operations on construction sites.

Our roofing SWMS pack covers 8 activities including roof tiling, metal roof sheeting, roof restoration, gutter and fascia installation, skylights, and height safety system installation. Each document addresses the critical hazards of roofing work including falls from roof edges, falls through fragile roof surfaces, falling objects, heat stress, and adverse weather conditions.

Key Hazards Covered

Falls from roof edges and eaves
Falls through fragile roof surfaces (skylights, sheeting)
Falling objects and tools from roof level
Heat stress from prolonged sun exposure
Manual handling of heavy roofing materials at height
Adverse weather conditions (wind, rain, lightning)

Relevant Australian Standards

AS/NZS 1891.1 Fall-arrest systems and harnesses
AS/NZS 4994.1 Temporary edge protection
AS 1562 Design and installation of sheet roof and wall cladding
AS/NZS 4576 Guidelines for scaffolding safety

Individual Documents — $21.21 each

	Document	Price
	Roof Tiling — Safe Work Method Statement Covers installation and replacement of concrete and terracotta roof tiles including ridge capping, bedding, and pointing on residential and commercial buildings. What's inside this document 6 work steps 11 hazards identified 11 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more PPE Requirements (with AS/NZS standards) Full body harness + lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (non-slip) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Gloves (AS/NZS 2161.1) P2 respirator (when cutting or stripping) (AS/NZS 1716) Australian Standards Referenced AS/NZS 4576 — Guidelines for scaffolding safety AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 4994.1 — Temporary edge protection AS/NZS 1801 — Occupational protective helmets AS/NZS 2210.3 — Safety, protective and occupational footwear	$21.21
	Roof Sheeting (Metal) — Safe Work Method Statement Covers installation and replacement of metal roof sheeting including Colorbond, Zincalume, and corrugated iron on residential and commercial structures. What's inside this document 6 work steps 10 hazards identified 10 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more WHS Reg 2011, Reg 291(1)(b) - Risk of fall into liquid or other substance PPE Requirements (with AS/NZS standards) Full body harness + retractable lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (non-slip sole) (AS/NZS 2210.3) Safety glasses with side shields (AS/NZS 1337.1) Cut-resistant gloves (AS/NZS 2161.3) Class 5 hearing protection (AS/NZS 1270) High-visibility vest (AS/NZS 4602.1) Australian Standards Referenced AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 4994.1 — Temporary edge protection AS/NZS 4389 — Safety mesh for fall prevention AS/NZS 4576 — Guidelines for scaffolding safety AS/NZS 1270 — Acoustics — Hearing protectors AS/NZS 4602.1 — High visibility safety garments	$21.21
	Roof Restoration and Repairs — Safe Work Method Statement Covers roof restoration work including pressure cleaning, repointing, rebedding ridge caps, sealing, priming and painting of existing roof surfaces on residential and commercial buildings. What's inside this document 5 work steps 9 hazards identified 9 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more PPE Requirements (with AS/NZS standards) Full body harness + lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (non-slip) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Chemical-resistant gloves (AS/NZS 2161.10) Organic vapour respirator (AS/NZS 1716) Waterproof clothing (pressure cleaning) (N/A) Australian Standards Referenced AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 4994.1 — Temporary edge protection AS/NZS 1716 — Respiratory protective devices AS/NZS 1801 — Occupational protective helmets AS/NZS 2210.3 — Safety, protective and occupational footwear	$21.21
	Gutter and Fascia Installation — Safe Work Method Statement Covers removal and installation of guttering, fascia boards, downpipes, and associated flashings on residential and commercial buildings. What's inside this document 5 work steps 8 hazards identified 8 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more PPE Requirements (with AS/NZS standards) Full body harness + lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (AS/NZS 2210.3) Cut-resistant gloves (AS/NZS 2161.3) Safety glasses (AS/NZS 1337.1) High-visibility vest (AS/NZS 4602.1) Australian Standards Referenced AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 1892.1 — Portable ladders — Metal AS/NZS 4576 — Guidelines for scaffolding safety AS/NZS 4994.1 — Temporary edge protection AS/NZS 4602.1 — High visibility safety garments	$21.21
	Roof Safety System Installation — Safe Work Method Statement Covers installation of permanent roof safety systems including roof anchor points, static lines, walkway systems, guardrail systems, and ladder brackets for ongoing maintenance access. What's inside this document 5 work steps 8 hazards identified 8 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more WHS Reg 2011, Reg 306 - Maintenance of plant (anchor points) PPE Requirements (with AS/NZS standards) Full body harness + twin-tail lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (non-slip) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Gloves (AS/NZS 2161.1) Hearing protection (AS/NZS 1270) Australian Standards Referenced AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 1891.4 — Industrial fall-arrest systems and devices — Selection, use and maintenance AS/NZS 4994.1 — Temporary edge protection AS/NZS 3760 — In-service safety inspection and testing of electrical equipment AS/NZS 1657 — Fixed platforms, walkways, stairways and ladders — Design, construction and installation	$21.21
	Asbestos Roof Work — Safe Work Method Statement Covers removal, repair, encapsulation, and over-cladding of asbestos-containing roofing materials including fibrous cement sheeting (super six, flat fibro) on residential and commercial buildings. Requires Class A or Class B asbestos removal licence depending on scope. What's inside this document 6 work steps 9 hazards identified 9 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more WHS Reg 2011, Reg 419 - Licensed asbestos removal work WHS Reg 2011, Reg 458 - Asbestos removal control plan PPE Requirements (with AS/NZS standards) P2 half-face respirator (non-friable) / P3 full-face respirator (friable) (AS/NZS 1716) Disposable coveralls type 5/6 (Category III Type 5/6) Full body harness + lanyard (AS/NZS 1891.1) Safety footwear (non-lace or taped laces) (AS/NZS 2210.3) Disposable gloves (AS/NZS 2161.1) Safety glasses (sealed / goggles for friable) (AS/NZS 1337.1) Hard hat (AS/NZS 1801) Australian Standards Referenced AS 2601 — The demolition of structures (includes asbestos removal procedures) AS/NZS 1716 — Respiratory protective devices AS/NZS 3544 — Industrial clothing AS/NZS 1891.1 — Industrial fall-arrest systems and devices SafeWork Australia Code of Practice: How to Safely Remove Asbestos SafeWork Australia Code of Practice: How to Manage and Control Asbestos in the Workplace WHS Reg 2011 Part 8.5 — Asbestos at the workplace WHS Reg 2011 Part 8.7 — Licensed asbestos removal work	$21.21
	Skylights and Roof Penetrations — Safe Work Method Statement Covers installation, replacement, and repair of skylights, roof ventilators, whirlybirds, flue penetrations, and other roof-mounted equipment requiring cutting or creating openings in the roof surface. What's inside this document 5 work steps 9 hazards identified 9 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more WHS Reg 2011, Reg 291(1)(c) - Risk of fall through an opening PPE Requirements (with AS/NZS standards) Full body harness + lanyard (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (non-slip) (AS/NZS 2210.3) Safety glasses (AS/NZS 1337.1) Cut-resistant gloves (AS/NZS 2161.3) Hearing protection (AS/NZS 1270) P2 respirator (when cutting) (AS/NZS 1716) Australian Standards Referenced AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 4994.1 — Temporary edge protection AS/NZS 3000 — Electrical installations (Wiring Rules) AS/NZS 1270 — Acoustics — Hearing protectors AS/NZS 1716 — Respiratory protective devices	$21.21
	Scaffold Erection and Use for Roofing — Safe Work Method Statement Covers erection, alteration, use, and dismantling of scaffolding for roofing projects including modular scaffold, tube and coupler systems, and mobile scaffold towers on residential and commercial sites. What's inside this document 5 work steps 10 hazards identified 10 control measures 5×5 risk matrix Worker sign-off section Legislation Referenced WHS Reg 2011, Reg 291(1)(a) - Risk of fall of 2m or more WHS Reg 2011, Reg 224 - Scaffolding work requiring high risk work licence WHS Reg 2011, Reg 225 - Basic scaffolding (up to 4m) PPE Requirements (with AS/NZS standards) Full body harness + lanyard (erection/dismantling) (AS/NZS 1891.1) Hard hat (AS/NZS 1801) Safety footwear (AS/NZS 2210.3) Gloves (AS/NZS 2161.1) Safety glasses (AS/NZS 1337.1) High-visibility vest (AS/NZS 4602.1) Australian Standards Referenced AS/NZS 4576 — Guidelines for scaffolding safety AS/NZS 1576.1 — Scaffolding — General requirements AS/NZS 1576.2 — Scaffolding — Couplers and accessories AS/NZS 1576.3 — Scaffolding — Prefabricated and tube-and-coupler scaffolding AS/NZS 1891.1 — Industrial fall-arrest systems and devices AS/NZS 1801 — Occupational protective helmets	$21.21

Roofing Toolbox Talk — Common Questions

How often should toolbox talks be held?

Most WHS guidelines recommend weekly toolbox talks, or before any new high-risk activity begins. Regular talks demonstrate ongoing safety consultation with workers.

What topics do your toolbox talks cover?

Each toolbox talk covers trade-specific hazards, safe work procedures, PPE requirements, and emergency protocols relevant to that trade's activities.

Do toolbox talks include an attendance register?

Yes. Every Toolbox Talk document includes an attendance register for worker sign-off, providing evidence of WHS consultation.

Are toolbox talks a legal requirement?

While not explicitly mandated by name, WHS legislation requires PCBUs to consult with workers on safety matters. Documented toolbox talks are the most common way to demonstrate this consultation.

Last updated: March 2026

Roofing Toolbox Talk

Roofing Complete Pack

Individual Documents — $21.21 each

Roofing Toolbox Talk — Common Questions

Other Trades You Might Need